Autoplay
Autocomplete
Previous Lesson
Complete and Continue
MikroTik Wireless Engineer with LABS
WLAN Fundamental
1- Introduction WLAN Fundamental (1:10)
2- Understand the Wireless terminology (12:32)
Wireless Tools on MikroTik
3- Introduction to Wireless Tools on MikroTik (0:54)
4- Frequency usage - Spectral Scan - Spectral History (13:15)
5- MikroTik Wireless Alignment tool (8:45)
6- Wireless Snooper and Sniff Tool (13:16)
7- Wireless Scan Tool and Reset Configuration (8:29)
Wireless Frequency mode and TX power change
8- Introduction to Wireless Frequency mode (1:19)
9- MikroTik Frequency modes Regulatory-domain Manual Tx power Superchannel (13:43)
10- Changing the TX power for a better signal reception (10:36)
MikroTik Wireless Data rate and chains
11- Introduction to Wireless data rate and chains (1:04)
12- Wireless Chains and difference between SISO and MIMO (9:18)
13- Avoid Data Rate flapping using the basics and supported data rate options (13:43)
Wireless Link Quality - Troubleshooting
14- Introduction - Wireless Link troubleshooting (1:08)
15- Wireless SNR CCQ and HW Frames (19:22)
16- Advanced Distance Noise Floor Threshold and HW Fragmentation Threshold (9:32)
17- RTS CTS CTS to Self HW protection Threshold and Adaptive Noise Immunity (14:48)
Channel Width, Channel Bonding & Guard interval
18- Introduction - What is channel width channel bonding and guard interval (1:04)
19- Channel Width and Channel Bonding (11:31)
20- Changing the Guard interval for more or less throughput (17:53)
Wireless Protocols: Nstreme vs NV2
21- Introduction Nstreme vs nv2 (1:05)
22- Configuring Nstreme and NV2 wireless protocols on MikroTik Routers (22:02)
23- NV2 additional settings (7:59)
Nstreme Dual
24- Introduction What is Nstreme Dual (2:16)
25- Configuring Nstreme Dual for a Wireless Point-to-Point link (17:05)
Wireless Bridging on MikroTik
26- Introduction to Wireless Bridging (1:51)
27- Station Bridge mode on MikroTik (17:04)
28- Station pseudobridge and Station pseudobridge clone modes on MikroTik (10:01)
MikroTik Wireless Repeater
29- Introduction What is a wireless repeaterzip (1:00)
30- Configuring the router as a wireless repeater using the repeater setup (10:06)
Wireless Bridging using EOIP and MPLS/VPLS
31- Introduction Wireless bridging with EOIP and MPLS VPLS (1:55)
32- Configuring Wireless Bridging using EOIP Tunnel (11:58)
33- Configuring Wireless Bridging using MPLS VPLS Tunnel (9:52)
Wireless Security
34- Introduction to Wireless Security (1:37)
35- Wireless security using Dynamic Static keys and EAP (20:37)
36- Management Protection to forbid De-authentication attacks on Wireless (7:41)
37- Default Authenticate and Access list (18:47)
38- Connect list to allow the station to connect to the right AP (17:38)
Wireless WDS and Mesh
39- Introduction to WDS (1:03)
40- Configuring WDS Dynamic mode using Station WDS and WDS Slave (21:48)
41- Configuring WDS Static mode using Station WDS and WDS Slave (7:52)
42- Wireless Mesh using HWMP+ for good wireless roaming (17:47)
MikroTik official trainings with Maher Haddad (3:27)
30- Configuring the router as a wireless repeater using the repeater setup
Lesson content locked
If you're already enrolled,
you'll need to login
.
Enroll in Course to Unlock